1. Connect the WDS or equivalent to the DLC-2.
2. Measure the PID value.
|
Monitor item (Definition)
|
Unit/Condition
|
Condition/Specification
|
Action
|
TCM terminal
|
|---|---|---|---|---|
|
24B_Duty
(Shift solenoid B)
|
%
|
• 2 or 4GR: 0%
• Other: 99%
|
• Inspect the shift solenoid valve B.
(See SOLENOID VALVE INSPECTION.)
|
2S
|
|
BOO_TCM
(Brake switch)
|
ON/OFF
|
• Brake pedal is depressed: ON
• Brake pedal is released: OFF
|
• Adjust the brake pedal.
• Inspect the brake switch.
(See BRAKE SWITCH INSPECTION.)
|
1G
|
|
CPP/PNP
(P/N position switch)
|
Drive/Neutral
|
• P or N position: Neutral
• R, D or M range: Drive
|
• Inspect the TR switch.
|
1D, 2B
|
|
DTC_CNT
(Number of DTCs detected)
|
N/A
|
• DTCs is detected: 1-255
• No DTCs are detected: 0
|
• Inspect the DTCs.
(See DTC TABLE [RC4A-EL].)
|
N/A
|
|
DWN SW
(Down switch)
|
ON/OFF
|
• M range, downshift: ON
• Other: OFF
|
• Inspect the selector lever component.
|
2D
|
|
ECT TCM
(ECT sensor)
|
°C, °F
|
• Indicates engine coolant temperature
|
• Inspect the ECT sensor.
• Inspect the PCM.
|
N/A
|
|
FDPDTC
|
N/A
|
• Pending code that caused FFD storage
|
N/A
|
N/A
|
|
GEAR
|
1st/2nd/3rd/4th
|
• 1GR: 1st
• 2GR: 2nd
• 3GR: 3rd
• 4GR: 4th
|
• Inspect the following PIDs: 24B_Duty, HC_Duty, LRB_Duty, TCCC
|
N/A
|
|
GEAR_RA
(Gear ratio)
|
N/A
|
• 1GR: 2.785
• 2GR: 1.545
• 3GR: 1.000
• 4GR: 0.694
• Reverse: 2.272
|
• Inspect the following PIDs: 24B_Duty, HC_Duty, LRB_Duty, OP_SW_24B, OP_SW_HC, OP_SW_LRB, TCCC
|
N/A
|
|
HC_Duty
(Shift solenoid C)
|
%
|
• 3 or 4GR: 0%
• Other: 99%
|
• Inspect the shift solenoid valve C.
(See SOLENOID VALVE INSPECTION.)
|
2V
|
|
LRB_Duty
(Shift solenoid F)
|
%
|
• R position or 1GR at M range: 0%
• Others: 99%
|
• Inspect the shift solenoid valve F.
(See SOLENOID VALVE INSPECTION.)
|
2P
|
|
LU_Duty
(TCC solenoid)
|
%
|
• TCC operation off: 0%
• TCC operation on: 99%
|
• Inspect the TCC shift solenoid valve.
(See SOLENOID VALVE INSPECTION.)
|
2W
|
|
MNL SW
(M range switch)
|
ON/OFF
|
• M range: ON
• Other: OFF
|
• Inspect the selector lever component.
|
1E
|
|
OP_SW_24B
(Oil pressure switch B)
|
ON/OFF
|
• 2 or 4GR: ON
• N position: OFF
|
• Inspect the oil pressure switch B.
|
2A
|
|
OP_SW_HC
(Oil pressure switch C)
|
ON/OFF
|
• 3 or 4GR: ON
• N position: OFF
|
• Inspect the oil pressure switch C.
|
2F
|
|
OP_SW_LRB
(Oil pressure switch F)
|
ON/OFF
|
• R position: ON
• N position: OFF
|
• Inspect the oil pressure switch F.
|
2H
|
|
OSS
(Output shaft speed signal)
|
rpm
|
• Indicates output shaft speed
|
• Inspect the vehicle speed sensor
|
2K
|
|
PCSV
(Pressure control solenoid)
|
ON/OFF
|
• Line pressure high: ON
• Line pressure low: OFF
|
• Inspect the pressure control solenoid valve.
(See SOLENOID VALVE INSPECTION.)
|
2X
|
|
RPM
(Engine speed)
|
rpm
|
• Engine speed 1,000 rpm: 1,000 rpm
|
• Inspect the TCM.
(See TCM INSPECTION.)
|
N/A
|
|
TCCC
(Shift solenoid A)
|
%
|
• 4GR: 99%
• Other: 0%
|
• Inspect the shift solenoid valve A.
(See SOLENOID VALVE INSPECTION.)
|
2Y
|
|
TFT
(ATF temperature)
|
°C, °F
|
• ATF 20 °C {68 °F}: 20 °C {68 °F}
• ATF 80 °C {176 °F}: 80 °C {176 °F}
|
• Inspect the TFT sensor.
|
2J
|
|
TFTV
(ATF temperature signal voltage)
|
V
|
• ATF 20 °C {68 °F}: 1.55 V
• ATF 60 °C {140 °F}: 0.7 V
|
• Inspect the TFT sensor.
|
2J
|
|
THOP
(Throttle position)
|
%
|
• CTP: 0%
• WOT: 100%
|
• Inspect the TCM.
(See TCM INSPECTION.)
|
N/A
|
|
TR
(Transmission range)
|
R/N/D
|
• R position: R
• N position: N
• D range: D
|
• Inspect the TR switch.
|
2B, 2C, 2E
|
|
TRD
(D range switch)
|
ON/OFF
|
• D range: ON
• Except D range: OFF
|
• Inspect the TR switch.
|
2E
|
|
TRR
(R position switch)
|
ON/OFF
|
• R position: ON
• Except R position: OFF
|
• Inspect the TR switch.
|
2C
|
|
TSS
(Turbine sensor)
|
rpm
|
• Ignition switch at ON position (engine off): 0 rpm
• Idle: 700-800 rpm
|
• Inspect the turbine sensor
(See TURBINE SENSOR INSPECTION.)
|
2G
|
|
UP SW
(Up switch)
|
ON/OFF
|
• M range, upshift: ON
• Other: OFF
|
• Inspect the selector lever component.
|
2I
|
|
VPWR
(Battery voltage)
|
V
|
• Ignition switch at ON position: B+
• Engine running: B+
|
• Inspect the ignition switch.
(See IGNITION SWITCH INSPECTION.)
• Inspect the battery.
(See BATTERY INSPECTION.)
|
1A, 2Z, 2AA
|
|
VSS
(Vehicle speed)
|
km/h, mph
|
• Indicates vehicle speed
|
• Inspect the VSS.
• Inspect ABS HU/CM.
• Inspect DSC HU/CM.
• Inspect PCM.
|
N/A
|